SUS410 Stainless Steel

in stock

 

We are the SUS 410 / SS 410 / 1.4006 Stainless Steel Supplier Malaysia. Stainless Steel X12Cr13 (SUS410) is the basic martensitic stainless steel; like most non-stainless steels it can be hardened by a “quench-and-temper” heat treatment.

With the strong global sourcing in Duplex Stainless Steel, our sales and supplier network including : Australia, Pakistan,  Malaysia, Singapore, Taiwan, China, Vietnam, Belgium, Japan, South Korea, Philippines, France, United Kingdom, Indonesia, Thailand, Hong Kong, China, Sweden, United States, Dubai, Finland, Brunei, Germany.

 

Leading Supplier of Stainless Steel 410

Specifications of Grade 410 Stainless Steel also equivalent to 
  • SUS410 | UNS S41000 | SS410 | 

 

Grade UNS No Old British Euronorm Swedish SS Japanese JIS
BS En No Name
SS410 S41000 410S21 56A 1.4006 X12Cr13 2302 SUS 410
** These comparisons are approximate only. The list is intended as a comparison of functionally similar materials not as a schedule of contractual equivalents. If exact equivalents are needed original specifications must be consulted.

 

Properties of SUS410 Stainless Steel

SS410 is the basic martensitic stainless steel; like most non-stainless steels it can be hardened by a “quench-and-temper” heat treatment. It contains a minimum of 11.5 per cent chromium, just sufficient to give corrosion resistance properties. It achieves maximum corrosion resistance when it has been hardened and tempered and then polished.

SUS410 is a general purpose grade often supplied in the hardened, but still machinable condition, for applications where high strength and moderate heat and corrosion resistance are required.

Martensitic stainless steels are optimized for high hardness, and other properties are to some degree compromised. Fabrication must be by methods that allow for poor weldability and usually the need for a final heat treatment.

Corrosion resistance of the martensitic grades is lower than that of the common austenitic grades, and their useful operating temperature range is limited by their loss of ductility at sub-zero temperatures and loss of strength by over-tempering at elevated temperatures.

 

Chemical Formula for SUS 410

Fe, |  <0.15% C |  11.5-13.5% Cr | >0.75% Ni | <1.0% Mn | <1.0% Si | <0.04% P | <0.03% S

 

Corrosion Resistance for SS410

Type 410 Stainless Steel resists dry atmosphere, fresh water, mild alkalis and acids, food, steam and hot gases. Must be hardened for maximum heat and corrosion resistance. Performance is best with a smooth surface finish. Less corrosion resistant than the austenitic grades and also less than 17% chromium ferritic alloys such as Grade 430.

 

Heat Resistance for SS 410

Good resistance to scaling up to approximately 650°C, but generally not recommended for use in temperatures between 400 and 580°C, because of the reduction in mechanical properties.

 

Heat Treatment for 410 Stainless Steel 

Annealing – Grade 410 stainless steel can be fully annealed at temperatures from 815 to 900 °C, followed by slow furnace cooling and air-cooling. Process annealing of grade 410 steels can be carried out at temperatures ranging from 650 to 760 °C and air-cooled.

Hardening – Hardening of type 410 stainless steels can be performed at 925 to 1010 °C, followed by air and oil quenching. Heavy sections of grade 410 need to be oil quenched. Tempering, to enhance the mechanical properties and hardness of grade 410 steels, follows this process. It is not recommended to perform tempering at temperatures from 400 to 580 °C.

 

Applications for Stainless Steel Grade 410 

SUS410 Stainless Steel can be used in the following applications : 

  • Bolts & Nults
  • Screws
  • Bushings
  • Pump and valve parts and shafts
  • Steam and gas turbine parts
  • Petroleum fractionating towers
  • Mine ladder rungs

 

Our Sales and Supplier Network in SUS410 / Grade 410 Stainless Steel : 

With over many years of experience and strong global sourcing networking in the market, we are proud to be the SUS 410 / SS 410 / Type 410 Stainless Steel Supplier and Exporter to :

  • Australia, Pakistan,  Malaysia, Singapore, Taiwan, China, Vietnam, Belgium, Japan, South Korea, Philippines, France, United Kingdom, Indonesia, Thailand, Hong Kong, China, Sweden, United States, Dubai, Finland, Brunei, Germany.

Besides, we have the full range of Stainless Steel sheets, Stainless Steel Round Bar, Stainless Steel Rods, Stainless Steel Plate which consists of 

300 Series Stainless Steel : SUS304, SUS304L, SUS309, SUS310, SUS316Ti, SUS317, SUS321, SUS347

400 Series Stainless Steel  : SUS403, SUS410, SUS420, SUS431, SUS440C, SUS630, SUS904L 

Nitronic 30, Nitronic 50, Nitronic 60

– Super Duplex S32750, S32760 

253MA 

Send via WhatsApp